Achso. Dann frag ich olli mal ob er den fehler rausprogrammieren kann wenn der kommt.
Beiträge von MetalSkinGaming
-
-
Kann ja dann nochmal schreiben wenn ich soweit bin
-
Nö wenn man den sensor und den widerstand drin lässt sollte keine mkl kommen
-
https://www.ebay.de/itm/50-x-8…ksid=p2057872.m2749.l2649
hatte mir die damals bestellt. Die müssten passen.
-
Laut schaltplan sind in den hinteren türen jeweils 2 verbaut einmal oben und einmal unten
-
Joa aber das Teil nervt mich sowieso also einfach raus und fertig.
-
Könntest ja Olli fragen ob der nen paar will zum weiterverkaufen. Dann wären vll in nem jahr oder so auch noch welche da falls es sich wer anders überlegt.
edit: Hab grad gesehen dass Olli schon welche im Shop hat. Dann hat sich das wohl erledigt.
-
wollte nur nochmal nachfragen. weil die im ami forum geschrieben haben dass damit der kat schneller kaputt geht oder so.
-
-
Würde mit der motorüberholung nicht zu lange warten sonst kann es sein dass deine housings schrott sind wenns dann soweit ist.
-
Evtl hat nen massepunkt am motor schlechten kontakt. Würd die mal alle durchschaun und evtl anschleifen
-
@taha696 nen wankelmotor kann man aber nicht einfach so mit irgendeinem kompressionstester messen. Da gibts extra einen für wankelmotoren.
Und weil du meintest vonwegen vorher informieren über das auto etc.
Da hast du dir wohl das falsche auto für sowas gekauft... -
Hallo,
Ich suche gerade pods für die a-säule. Habe bis jetzt aber nur welche aus amerika gefunden und die kosten mit versand dann fast 300€.
Weiß jemand ob man sowas auch in deutschland irgenwo kaufen kann.
-
Das was du im video siehst ist 2 step/ antilag.
-
jo hab ich schon gemacht
-
Audioausgabe über A2DP und Youtube funktioniert
-
jo hab mir das duchgelesen hab jetz die 4 zeilen noch hinzugefügt, geht allerdings trotzdem nicht
-
ob am dac grad was angeschlossen ist is egal oder?
-
hier die config
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4# uncomment for composite PAL
#sdtv_mode=2#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
dtparam=i2s=on
#dtparam=spi=on# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtoverlay=hifiberry-dacplus
dtparam=audio=off
#dtoverlay=vc4-kms-v3d
gpu_mem=256
dtoverlay=vc4-fkms-v3d
disable_splash=1und habe den dac hier https://www.hifiberry.com/shop/boards/hifiberry-dac-pro/
-
habs jetzt mit mikrofon probiert geht allerdings immernoch nicht